Abrasive Cut-Off Disk, Non-Ferrous (3-1/4 Dia., 10mm Hole)

Name: Abrasive Cut-Off Disk, Non-Ferrous (3-1/4 Dia., 10mm Hole)
Brand: WESTFIELD GRINDING WHEEL CO.
SKU: 82594
Price: 12.95 USD
Availability: InStock

$12.95 USD

Shipping calculated at checkout.

SKU

82594

Quantity

Our Price

Abrasive Cut-Off Disk for the MicroLux Table Saw and Heavy Duty Miter/Chop Saw

Made from high-quality abrasive material for precision cutting
Suitable for use with non-ferrous materials such as aluminum, brass, and copper
3-1/4 inches in diameter, making it ideal for smaller workpieces
10mm hole size is a perfect fit for our 80463 Table Saw
Provides a clean, precise cut with minimal burring or chipping

WARNING: Some dusts created by using power tools contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Use adequate protection. For more information, go to: www.p65warnings.ca.gov

More Product Details

Silicon carbide abrasive disk for cutting off non-ferrous materials like brass, aluminum, copper, bronze, zinc, white metal, etc. 3-1/4 inch diameter x 1/16 inch thick with 10mm arbor.

Instructions

Shipping & Returns

We hope you will be completely satisfied with your order...but, if an item does not meet your expectations, you may return it in as-new condition within 30 days of delivery for a replacement, exchange or refund of the purchase price.

You may want to know...

Brand: Micro-Mark

Item Weight: 0.08 lb

Item Dimensions: 3.25 x 3.25 x 2 inches

List Price: $15

Manufacturer ETA:

Most orders are shipped complete within 2 business days; however, if we must ship a partial order due to an out-of-stock situation, merchandise will not be charged to your credit card until shipment is made.

Good quality foam clay

Unlike any air dry clay I've used .
Very easy to manipulate , doesn't stick to your fingers .
Can be made into paper thin sheets that hold their shape .

Thick sections will take well over 24 hours to dry out ; high water weight when fresh .
Evaporation slows down considerably once the outer " crust " dries on thick pieces .

After 24 hours @ 78 degrees and about 60% humidity , the 3.1 gram sample I experimented with weighs 1.2 grams .
.. and after 48 hrs weighs just 1/2 gram ,, and I don't think it's fully dry yet .

Definitely worth the price .
Very versatile .

My only complaint is the bag it comes in .
It is a zipper lock bag but you need to remove a fair amount of the product before you'll be able to engage the zipper .
It's stuffed full when new .
I fit the bag into a plastic container ( Folgers coffee 43.5oz can ) with an inch of water at the bottom to ensure it doesn't dry out until I use enough to be able to close the bag .
Most likely keep it in that can regardless , just to be safe .

Quality miniature model paint

This stuff is comparable to Vallejo paints which everyone in the hobby already knows are tried and true. I honestly would not be able to tell the difference between the 2 brands looking at a finished model or trying to paint with it. The price is about the same but this includes slightly bigger bottles with a better design on the lid and seem to come with a plastic mixer ball already inside but its hard to tell for sure. This paint set also includes a paint thinner and cleaner for airbrushing. Its really hard to beat the price and value of this paint set for anyone wanting to have a quality paint job on something. I would say its near impossible.

A reasonably competent tool!

Works reasonably well for the low cost. I found it boggs down with very little pressure in hardwood, so a light touch is required for small carvings. The diamond point does do a nice job etching on steel, however. I found I had good control of the etching process using it on steel tools.

I bought an accessory pack of two additional bits with the tool.

Abrasive Cut-Off Disk, Non-Ferrous (3-1/4 Dia., 10mm Hole)

Abrasive Cut-Off Disk for the MicroLux Table Saw and Heavy Duty Miter/Chop Saw

You may want to know...

Customer Reviews

Let customers speak for us